[Jun 23, 2022] Get New JN0-104 Certification – Valid Exam Dumps Questions [Q86-Q107]

Rate this post

[Jun 23, 2022] Get New JN0-104 Certification – Valid Exam Dumps Questions

100% Passing Guarantee – Brilliant JN0-104 Exam Questions PDF

NO.86 Which of the following parameters can be used to create a static route with a next-hop that is not directly connected to the router?

indirect

next-hop

recursive

resolve

NO.87 Which two methods keep a Junos device operational if the primary storage device fails? (Choose two.)

Create a recovery snapshot.

Enable the ephemeral database.

Enable J-Web for device management.

Create a rescue configuration.

NO.88 Which of these is the default action for firewall filters?

log

discard

reject

NO.89 Click the Exhibit button

Referring to the exhibit, what will be the source address for packets egressing et-0/0/34.07

10.20.0.1

10.30.0.1

10.10.0.1

10.40.0.1

NO.90 What is considered a logical interface property on a Junos device?

MAC address

duplex setting

protocol family

clocking

NO.91 What does it mean by ge-0/1/2?

FPC 0, Slot 1, Port 2

Port 0, FPC 1, Slot 2

Slot 0, Port 1, FPC 2

NO.92 Which two conditions must exist in a Junos device for traffic to transit the device to a specific destination? Choose Two

A forwarding table entry for that destination must exist

A routing policy must be in place on the device

A firewall filter must exist to allow traffic to reach that destination

A routing table entry for that destination must exist

NO.93 Which of these are valid match criteria for a routing policy? (Choose two)

prefix list

port

time-to-live (TTL)

OSPF area ID

NO.94 What is the maximum number of configurations, by default, that are recoverable using the rollback command?

100

NO.95 Exhibit:

Which statement is correct when traffic is received from 10.10.10.4?

The traffic is only rejected

The traffic is only accepted

The traffic is counted and accepted

The traffic is counted and rejected

NO.96 Which layer of the TCP/IP model is tasked with delivering packets to the destination?

Network Layer

Application Layer

Internet Layer

Transport Layer

NO.97 What is the default keepalive time for BGP?

30 seconds

10 seconds

90 seconds

60 seconds

NO.98 Which of these are true about the primary address of an interface? (Choose two)

By default, the primary address on an interface is selected as the numerically highest local address configured on the interface.

The primary address is used when you have multiple IP addresses belonging to the same subnet on the same interface.

It is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interface

It can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interface.

NO.99 Which of these methods can be used to announce static routes found in the routing table to OSPF peers?

Apply an import policy to the static routes that injects the static routes into OSPF.

Apply an export policy to OSPF that injects the static routes into OSPF.

Apply an export policy to the static routes that injects the static routes into OSPF.

Apply an import policy to OSPF that injects the static routes into OSPF.

NO.100 What are the usable hosts on the 192.168.1.24/29 network?

.24 through .48

.24 through .32

.25 through .30

.35 through .31

NO.101 Which command will display the detailed Routing Engine status and its temperature?

show chassis routing-engine

show chassis status

show chassis environment

show chassis temperatures

NO.102 At which hierarchy would you configure a static MAC address for interface ge-0/0/0?

[edit interfaces ge-0/0/0 unit 0]

[edit interfaces ge-0/0/0]

[edit interfaces ge-0/0/0 unit 0 family inet]

[edit interfaces ge-0/0/0 unit 0 family inet address 172.25.11.2/24]

NO.103 Which of these commands can be used to troubleshoot routing issues and check the path to the destination 192.168.1.1? (Choose three)

user@router> traceroute 192.168.1.1

user@router> ping record-route 192.168.1.1

user@router# run traceroute 192.168.1.1

user@router# traceroute 192.168.1.1

user@router# ping record-route 192.168.1.1

NO.104 Which command do you use to show component and environmental status?

show chassis alarms

show system chassis environment

show chassis environment

show chassis status

NO.105 You successfully established a BGP session with a peer, but do not see any routes learned from the peer.
What would cause this problem?

A routing policy is blocking BGP from learning the routes

A security policy is blocking BGP from learning the routes

Unicast reverse-path-forwarding is blocking BGP from learning the routes

The firewall filter is blocking BGP from learning the routes

NO.106 How does the PFE handle unicast transit traffic destined for an entry that exists in the forwarding table?

It forwards the traffic to the local system for further processing

It forwards the traffic through one egress port towards its destination

It forwards the traffic through multiple egress ports

It forwards the traffic through an internal link to the RE

NO.107 Which statement is true about the longer router-filter match type?

All router within the specified prefix that are longer than given prefix are considered a match.

All router within the specified prefix that are longer than the given prefix up to a defined acceptable prefix length are considered a match.

All router within the specified prefix that are longer than or equal to the given prefix are considered a match.

All router within the specified prefix that are longer or equal to the given prefix up to a defined acceptable prefix length are considered a match.

Loading …

Free JN0-104 braindumps download: https://www.validexam.com/JN0-104-latest-dumps.html

[Jun 23, 2022] Get New JN0-104 Certification – Valid Exam Dumps Questions [Q86-Q107]

Written by admin

Leave a Reply Cancel reply

JN0-104 Practice Tests

Related Certifications

Recent Posts

Archives

Categories