[Dec-2022] Get 100% Real JN0-635 Free Online Practice Test [Q73-Q87]

admin JN0-635 Juniper December 10, 2022

Rate this post

[Dec-2022] Get 100% Real JN0-635 Free Online Practice Test

BEST Verified Juniper JN0-635 Exam Questions (2022)

JN0-635 Exam Process

The Juniper JN0-635 test will continue for 120 minutes. Besides, there are 65 multiple-choice items. You can get to know your pass/fail status immediately after the official test. Once you successfully clear such an exam and obtain your JNCIP-SEC certification, it is valid for three years.

NEW QUESTION 73
How does secure wire mode differ from transparent mode?

In secure wire mode, security policies cannot be used to secure intra-VLAN traffic

In secure wire mode, no switching lookup takes place to forward traffic

In secure wire mode, traffic can be modified using source NAT

In secure wire mode, IRB interfaces can be configured to route inter-VLAN traffic

NEW QUESTION 74
You are using IDP on your SRX Series device and are asked to ensure that the SRX Series device has the latest IDP database, as well as the latest application signature database.
In this scenario, which statement is true?

The application signature database cannot be updated on a device with the IDP database installed.

You must download each database separately.

The IDP database includes the latest application signature database.

You must download the application signature database before installing the IDP database.

NEW QUESTION 75
Click the Exhibit button.

You are asked to look at a configuration that is designed to take all traffic with a specific source IP address and forward the traffic to a traffic analysis server for further evaluation. The configuration is not working as intended.
Referring to the exhibit, which change must be made to correct the configuration?

Apply the filter as an input filter on interface xe-0/2/1.0

Create a routing instance named default

Apply the filter as an input filter on interface xe-0/0/1.0

Apply the filter as an output filter on interface xe-0/1/0.0

NEW QUESTION 76
You have a remote access VPN where the remote users are using the NCP client. The remote users can access the internal corporate resources as intended; however, traffic that is destined to all other Internet sites is going through the remote access VPN. You want to ensure that only traffic that is destined to the internal corporate resources use the remote access VPN.
Which two actions should you take to accomplish this task? (Choose two.)

Enable IKEv2 within the VPN configuration on the SRX Series device

Configure split tunneling on the NCP profile on the remote client

Configure the necessary traffic selectors within the VPN configuration on the SRX Series device

Enable the split tunneling feature within the VPN configuration on the SRX Series device

NEW QUESTION 77
You configured a security policy permitting traffic from the trust zone to the DMZ zone, inserted the new policy at the top of the list, and successfully committed it to the SRX Series device. Upon monitoring, you notice that the hit count does not increase on the newly configured policy.
In this scenario, which two commands would help you to identify the problem? (Choose two.)

user@srx> show security zones trust detail

user@srx> show security shadow-policies from zone trust to zone DMZ

user@srx> show security match-policies from-zone trust to-zone DMZ source-ip 192.168.10.100/32 destination-ip 10.10.10.80/32 protocol tcp source-port 5806 destination-port 443

user@srx> show security match-policies from-zone trust to-zone DMZ source-ip 192.168.10.100/32 destination-ip 10.10.10.80/32 protocol tcp source-port 5806 destination-port

NEW QUESTION 78
You opened a support ticket with JTAC for your Juniper ATP appliance. JTAC asks you to set up access to the device using the reverse SSH connection.
Which three setting must be configured to satisfy this request? (Choose three.)

Enable JTAC remote access

Create a temporary root account.

Enable a JATP support account.

Create a temporary admin account.

Enable remote support.

NEW QUESTION 79
Click the Exhibit button.

You have configured tenant systems on your SRX Series device.
Referring to the exhibit, which two actions should you take to facilitate inter-TSYS communication? (Choose two.)

Place the logical tunnel interfaces in a virtual router routing instance in the interconnect switch

Place the logical tunnel interfaces in a VPLS routing instance in the interconnect switch

Connect each TSYS with the interconnect switch by configuring INET configured logical tunnel interfaces in the interconnect switch

Connect each TSYS with the interconnect switch by configuring Ethernet VPLS configured logical tunnel interfaces in the interconnect switch

NEW QUESTION 80
Referring to the configuration shown in the exhibit, which statement explains why traffic matching the IDP signature DNS:OVERFLOW:TOO-LONG-TCP-MSG is not being stopped by the SRX Series device?

The security policy dmz-pol1 has an action of permit.

The IDP policy idp-pol1 is not configured as active.

The IDP rule r2 has an ip-action value of notify.

The IDP rule r1 has an action of ignore-connection.

NEW QUESTION 81
Click the Exhibit button.

Which type of NAT is shown in the exhibit?

NAT46

NAT64

persistent NAT

DS-Lite

NEW QUESTION 82
Click the Exhibit button.

You have configured tenant systems on your SRX Series device.
Referring to the exhibit, which two actions should you take to facilitate inter-TSYS communication?
(Choose two.)

Place the logical tunnel interfaces in a virtual router routing instance in the interconnect switch

Place the logical tunnel interfaces in a VPLS routing instance in the interconnect switch

Connect each TSYS with the interconnect switch by configuring INET configured logical tunnel interfaces in the interconnect switch

Connect each TSYS with the interconnect switch by configuring Ethernet VPLS configured logical tunnel interfaces in the interconnect switch

NEW QUESTION 83
Click the Exhibit button.

A host is unable to communicate with a webserver.
Referring to the exhibit, which statement is correct?

The webserver is not listening for traffic on port 80

A policy is denying the traffic between these two hosts

A session is created for this flow

The session table is running out of resources

NEW QUESTION 84
Click the Exhibit button.

You have recently committed the IPS policy shown in the exhibit. When evaluating the expected behavior, you notice that you have a session that matches all the rules in your IPS policy.
In this scenario, which action would be taken?

drop packet

no-action

close-client-and-server

ignore-connection

NEW QUESTION 85
The monitor traffic interface command is being used to capture the packets destined to and the from the SRX Series device.
In this scenario, which two statements related to the feature are true? (Choose two.)

This feature does not capture transit traffic.

This feature captures ICMP traffic to and from the SRX Series device.

This feature is supported on high-end SRX Series devices only.

This feature is supported on both branch and high-end SRX Series devices.

NEW QUESTION 86
Your network includes SRX Series devices at the headquarters location. The SRX Series devices at this location are part of a high availability chassis cluster and are configured for IPS. There has been a node failover.
In this scenario, which statement is true?

Existing sessions continue to be processed by IPS because of table synchronization.

Existing sessions are no longer processed by IPS and become firewall sessions.

Existing session continue to be processed by IPS as long as GRES is configured.

Existing sessions are dropped and must be reestablished so IPS processing can occur.

NEW QUESTION 87
You are asked to ensure that your IPS engine blocks attacks. You must ensure that your system continues to drop additional malicious traffic without additional IPS processing for up to 30 minutes. You must ensure that the SRX Series device does send a notification packet when the traffic is dropped.
Which statement is correct?

Use the IP-Block action.

Use the Drop Packet action.

Use the Drop Connection action.

Use the IP-Close action.