Exam Questions Answers Braindumps H12-831_V1.0 Exam Dumps PDF Questions [Q70-Q90]

Rate this post

Exam Questions Answers Braindumps H12-831_V1.0 Exam Dumps PDF Questions

Download Free Huawei H12-831_V1.0 Real Exam Questions

QUESTION 70
As shown in the figure, all interfaces of the router enable OSPF, among which R4 and R5 can establish OSPF virtual connections.

TRUE

FALSE

QUESTION 71
Which of the following Community attributes can ensure that the propagation range of BGP routing entries is only within the AS? (Multiple choice)

No_Export

No_Export_Subconfed

Interne

No_Advertise

QUESTION 72
Which of the following statements about MUX VLANs are true?

eachGroup VLANmust bind aPrincipal VLAN

Separate VLANscan andMUX VLANall withinVLANcommunication

eachSeparate VLANsmust bind aPrincipal VLAN

Principal VLANcan andMUX VLAIall withinVLANcommunication

QUESTION 73
A network engineer outputs the following information when troubleshooting OSPF. Based on this, determine which reason causes the adjacency relationship to fail to be established normally?

Authentication password is not-consistent

Regional type is not-consistent

The interval for sending Hello messages is not-consistent

The IP address mask of the interface is not-consistent

QUESTION 74
IEIF has extended the functions of OSPF by taking advantage of the strong scalability of OSPF. To enable it to support IPv6 networks, the expanded protocol is called OSPFv3, and OSPFv3 is compatible with OSPFv2.

TRUE

FALSE

QUESTION 75
As shown in the figure, all interfaces of the router enable OSPF. The IP address identified in the figure is the IP address of the oopback0 interface of the device. Loopback0 of R1 and R2 is advertised in area 1, Loopback0 of R4 is advertised in area 0, and Loopback0 of R3 and R5E are advertised in area 2, which of the following IP addresses can ping each other? (Multiple choice)

10.0.2.2 and 10.0.3.3. (Not counted when receiving Category 3 in non-backbone areas)

10.0.3.3 and 10.0.5.5 (Class 1 in the same area)

10.0.4.4 and 10.0.2.2. (3 types of normal calculation)

10.0.2.2 and 10.0.5.5 (not counted when receiving Category 3 in non-backbone areas)

QUESTION 76
Regarding the description of the encapsulation format of labels in MPLS, the correct one is

MPLSThe total length of a single label is4bytes(32bits)

For Ethernet,PPPpacket, the tag stack is like ‘shim*-between the L2 header and the data: yesVLAN tagTime,MPLShead on the ether head withVLAN tagbetween

in the labelSfield:lbit,Used to identify whether the label is the bottom label of the stack, the value is1is indicated as the penultimate layer label

in the labelTTLfields andIPgroupedTTL( Time To Live.,time-to-live) is similar in meaning and also has the effect of preventing loops

QUESTION 77
From this picture, we can judge

If not configured aboutAS_Pathrouting strategy, then3002:-4/128 -must not originate from AS 65001

R1does not have3002:3/128and3002.-4/128routing

R1have3002.-3/128and3002:.4/128routing

If not configured aboutAS_Pashrouting strategy, then3002:4/28must have originated from AS 65001

QUESTION 78
In an operator’s MPLSVPN network, there are two devices PE1 and PE2 for MPLSVPN data forwarding. PE1 receives a private network route of 172.16.1.0/24 from the client, and converts it to a VPNv4 route on PE1 and assigns a label of 1027 Released to PE2. The outgoing label of the MPLS LSR-ID of PE2 reaching PE1 is 1025o When a client on PE2 accesses 172.16.1.0/24, the frame sent by PE2, the inner and outer labels should be a combination of the following 6 options?

outer layer label:1025:inner label:1027

outer layer label:1027:inner label:1027

Layer Label:1027:inner label:1025

Layer Label,1025:inner label:1025

QUESTION 79
The router ID of OSPF V3 needs to be configured in dotted decimal with a length of 128 bits.

True

False

QUESTION 80
OSPFv2 is an IGP running on an IPv4 network; OSPFv3 is an IGP running on an IPv6 network. The basic working mechanism of OSPFv3 is the same as OSPFv2, such as the election of DR and BDR. As shown in the figure, an engineer uses three routers to test IPv6 services. He wants to realize the interconnection and interoperability of IPv6 networks by running OSPFv3.

Which of the following statements regarding the election of DR on this network is correct?

After the network converges, the engineer changes the priority of R1 to 100, the priority of R2 to 10, and the default value of R3. When the network converges again, R1 is DR and R2 is BDR

After the network converges, a new device R4 is added to the broadcast link, and the priority of R4 is 150. When the network converges again, R4 is the DR

After the network converges, R1 is powered off and restarted. When the network converges again, R3 is the DR

After the network converges, R1 is the DR

QUESTION 81
Which of the following descriptions is correct about configuring static LSPs in MPLS networks?

when a certainLSRforEgress LSR, you only need to configureIn Label,The range is 16-1023

when a certainLSRforTransit LSR, you need to configureIn LabelandOut labeljn LabelThe range is 16~1023,Out LabelThe range is16~1048575

when a certainLSRforTransit LSRneed to be configured at the same timeIn LabelandOut Label,The range is 16-1023

when a certainLSRforIngress LSR, just configureOut Label,The range is 16~1048575

QUESTION 82
Configure under a certain interface: isis timer hello 5 leve1-2, which of the following statements is correct?

The interval for sending Level-2 hello packets on this interface is 5s

The hello packet sending interval of Level-1 and Leval-2 of this interface is 3s.

The interval for sending Level-2 CSNP packets of this interface is 5s

The interval for sending Level-1 hello packets on this interface is 5s

QUESTION 83
According to the configuration shown in the figure below, you can know that R4 has an interface advertised into IS-IS?

QUESTION 84
According to this picture, the door can be judged?

R4belong only toLevel-2

system-IDforee8c.a0c2.baf2device whose type isLevel-1-2

system-IDforee8a0c2.baf2device whose type isLevel-1

R4belong only toLevel-1

QUESTION 85
Ethernet is a broadcast-enabled network, and once there are loops in the network, this simple factory broadcast mechanism can have disastrous consequences. Which of the following phenomena may be caused by loops?

CPUOccupancy exceeds70%

The device cannot log in remotely

use on devicedisplay interfaceWhen commanding to view interface statistics, it is found that the interface receives a large number of broadcast packets

pass throughpingSerious packet loss during network test with command

QUESTION 86
The routing attributes of the three routing entries are shown in the figure. Assuming that the next hops of the three routing entries are all reachable, when these three routing entries are After the entries arrive at the BP router in order, by default, BGP will finally call a route entry?

Route B

Route C

Route A

slightly

QUESTION 87
As shown in the figure, on the R1 router, network administrator A sends the routing entry to R2 through the routing policy After modifying the MED value, you can control the path of traffic entering the AS100

True

False

QUESTION 88
As shown in the figure, MPLS LSP is configured in the network, and the goal is to establish an LDP session between SWA and SWB, then which of the following statement is correct?