Download Cisco 300-615 Mock Test Study Material [Q50-Q69] : Valid Premium Exam : http://premium.validexam.com

NO.50 Refer to the exhibit.

A client configures an upgrade of its Cisco Nexus switches that are connected to the Cisco ACI controller, such that the switches are upgraded one at a time. After the upgrade is run, it is discovered that both Cisco Nexus switches were upgraded simultaneously. Which two actions ensure that the switches upgrade one at a time? (Choose two.)

Configure the *Do not pause on failure and do not wait on cluster health” Run Mode

Choose the ‘Pause upon upgrade failure” Run Mode

Select the “Graceful Maintenance” checkbox

Place each leaf switch in a different upgrade group

Check the Ignore Compatibility” checkbox

NO.51 Refer to the exhibit.

An engineer is performing a health check on ACI. Which statement about interface Ethernet 1/11 is true?

The interface is working correctly and fully operational, but it is not in use.

The interface policy is misconfigured.

“out-of-service” is the default interface status in ACI.

“out-of-service” indicates that no service graph is in use for this interface.

NO.52 Refer to the exhibit. One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address on SWITCH-VTEP-2 and then dropped. Which action resolves the issue?

Configure a distributed anycast gateway on both peers

Configure ip arp synchronize under the VPC domain on both peers

Configure peer-gateway under the VPC domain on both peers

Configure a different secondary IP address for one of the vPC peers

NO.53 Refer to the exhibit.

An OSPF adjacency between Router-A and Router-B cannot reach the FULL state. Which action resolves the issue?

Adjust the MTU on Router-A to 1600.

Disable the check of the MTU value.

Set the OSPF media type to point-to-point.

Adjust the MTU on Router-B to 1604.

NO.54 Refer to an exhibit.

An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?

Save the system image in NVRAM.

Use the same system image as the kickstart image.

Load a new system image.

Reload the same system image.

NO.55 Refer to the exhibit.

The vPC between switcM and switch2 does not work. Which two actions resolve the problem? (Choose two.)

Configure the IP address on the interface.

Activate VLANs on the vPC.

Configure one of the switches as primary for the vPC.

Correct the configuration of the vPC peer link and the vPC peer keepalive.

Match the vPC domain ID between the two devices.

NO.56 Refer to the exhibit.

The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?

VSAN 1 is suspended.

The SFP is unsupported.

Trunk mode must be activated.

The interface is in an incorrect mode.

NO.57 Refer to the exhibit.

The HSRP instance on both switches is showing as active. Which action resolves the issue?

Configure the HSRP timers to be the same.

Allow VLAN 100 between the switches.

Configure the IP address of N9K-B on the same subnet as N9K-A.

Configure preempt on only one of the switches.

NO.58 Refer to the exhibit.

The HSRP configuration in the exhibit fails to function. Which action resolves this issue?

Enable IP redirects.

Set the MTU to 1500 bytes.

Configure HSRP version 2.

Configure the same HSRP group on both devices.

NO.59 Refer to the exhibit.

An engineer must strictly enforce the port security configuration database in the Fibre Channel fabric. A new device has been connected to the Fibre Channel storage interface that was configured for port security. The port security was enabled for the VSAN that the port belongs to. Despite the configuration, the rogue devices can log into the fabric. Which action resolves the issue?

Commit the active database with the port-security database copy vsan 1 command

Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command

Disable CFS distribution with the no port-security distribute vsan 1 command

Commit the changes with the port-security commit copy vsan 1 command

NO.60 An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.

NO.61 Drag and drop the commands from the left onto the correct categories on the right.

NO.62 Refer to the exhibit.

An engineer is investigating a role mapping issue on a switch. The users report that they cannot view the IP addresses under the tenant “corp”. Which action resolves the issue?

Add the users to the RADIUS server.

Update the UNIX ID.

Configure the correct secret password between the APIC and the RADIUS server.

Add the updated avpair to include/corp/admin/

NO.63 Refer to the exhibit.

An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?

Configure the role name to match the group name on Microsoft Active Directory.

Include specific users into MDS role configuration.

Configure SSH logins on Cisco MDS switch.

Integrate Cisco MDS with Microsoft Active Directory.

NO.64 Drag and drop the commands from the left onto the correct categories on the right.

NO.65 Refer to the exhibit.

The cURL command fails to complete. Which action resolves the problem?

Remove “.json” from the URL.

Include -p “password” in the command.

Add -H “X-Auth-Token” to the command.

Change “.json” to “.xml” at the end of the URL.

NO.66 Refer to an exhibit.

An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?

Save the system image in NVRAM.

Use the same system image as the kickstart image.

Load a new system image.

Reload the same system image.

NO.67 Refer to the exhibit.

Refer to the exhibit The EEM applet must generate a syslog message whena BGP adjacency faps. This message must be displayed to the console of the switch. However, when a BGP adjacency failure is simulated, no syslog message is displayed. Which action resolves the issue?

Add the event-default action statement.

Modify the policy to use the snmp trap action.

Adjust the policy to match an SNMP OID.

Set the logging priority to Wamings.

NO.68 An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.

NO.69 A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity. However, after the server is rebooted, the host is not accessible on the network Which action resolves the issue?

Remove all existing vNICs and add them in the desired order.

Build a new service profile with the desired network configuration

Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs

Create a vNIC placement policy to avoid adapter renumbering

Download Cisco 300-615 Mock Test Study Material [Q50-Q69]

The benefit of obtaining the Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Exam Certification