Free 300-410 Exam Files Downloaded Instantly 100% Dumps & Practice Exam [Q225-Q246] : Valid Premium Exam : http://premium.validexam.com

NEW QUESTION 225

Refer to the exhibit. During troubleshooting it was discovered that the device is not reachable using a secure web browser.
What is needed to fix the problem?

permit tcp port 443

permit udp port 465

permit tcp port 465

permit tcp port 22

NEW QUESTION 226
Drag and drop the DHCP messages from the left onto the correct uses on the right.

Explanation

DHCPACK
The server-to-client communication with configuration parameters, including committed network address.
DHCPINFORM
The client-to-server communication, asking for only local configuration parameters that the client already has externally configured as an address.
DHCPNAK
The server-to-client communication, refusing the request for configuration parameter.
DHCPDECLINE
The client-to-server communication, indicating that the network address is already in use Reference:
https://www.cisco.com/c/en/us/support/docs/ip/dynamic-address-allocation-resolution/27470-100.html DHCPINFORM: If a client has obtained a network address through some other means or has a manually configured IP address, a client workstation may use a DHCPINFORM request message to obtain other local configuration parameters, such as the domain name and Domain Name Servers (DNSs). DHCP servers receiving a DHCPINFORM message construct a DHCPACK message with any local configuration parameters appropriate for the client without allocating a new IP address. This DHCPACK will be sent unicast to the client.
DHCPNAK: If the selected server is unable to satisfy the DHCPREQUEST message, the DHCP server will respond with a DHCPNAK message. When the client receives a DHCPNAK message, or does not receive a response to a DHCPREQUEST message, the client restarts the configuration process by going into the Requesting state. The client will retransmit the DHCPREQUEST at least four times within 60 seconds before restarting the Initializing state.
DHCPACK: After the DHCP server receives the DHCPREQUEST, it acknowledges the request with a DHCPACK message, thus completing the initialization process.
DHCPDECLINE: The client receives the DHCPACK and will optionally perform a final check on the parameters. The client performs this procedure by sending Address Resolution Protocol (ARP) requests for the IP address provided in the DHCPACK. If the client detects that the address is already in use by receiving a reply to the ARP request, the client will send a DHCPDECLINE message to the server and restart the configuration process by going into the Requesting state.
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/dynamic-address-allocation-resolution/27470-100.html

NEW QUESTION 227
R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?

R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.

R1 does not accept any routes other than 192.168.130.0/24

R1 does not forward traffic that is destined for 192.168.30.0/24

Network 192.168.130.0/24 is not allowed in the R1 table

NEW QUESTION 228
Drag and Drop Question
Drag and drop the SNMP attributes in Cisco IOS devices from the onto he correct SNMPv2c or SNMPv3 categories on the right.

NEW QUESTION 229
Which mechanism must be chosen to optimize the reconvergence time for OSPF at company location
407173257 that is less CPU-intensive than reducing the hello and dead timers?

BFD

Dead Peer Detection keepalives

SSO

OSPF demand circuit

NEW QUESTION 230
Drag and drop the LDP features from the left onto the descriptions on the right

NEW QUESTION 231
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.

NEW QUESTION 232
Refer to the exhibit.

The administrator can see the traps for the failed login attempts, but cannot see the traps of successful login attempts. What command is needed to resolve the issue?

Configure logging history 2

Configure logging history 3

Configure logging history 4

Configure logging history 5

NEW QUESTION 233
Refer to the exhibit.

AS111 is receiving its own routes from AS200 causing a loop in the network. Which configuration provides loop prevention?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

NEW QUESTION 234

An engineer sets up a DMVPN connection to connect branch 1 and branch 2 to HQ branch 1 and branch 2 cannot communicate with each other. Which change must be made to resolve this issue?

Option A

Option B

Option C

Option D

NEW QUESTION 235

Refer to the exhibit The engineer configured route redistribution in the network but soon received reports that R2 cannot access 192 168 7 0/24 and 192 168 15 0/24 subnets Which configuration resolves the issue?

Option A

Option B

Option C

Option D

NEW QUESTION 236

Refer to the exhibit A company builds WAN infrastructure between the head office and POPs using DMVPN hub-and-spoke topology to provide end-to-end communication All POPs must maintain point-to-point connectivity with the head office Which configuration meets the requirement at routers R12 and R13?

Option A

Option B

Option C

Option D

NEW QUESTION 237
Refer to the exhibit.

After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?

Set the administrative distance 100 under the RIP process on R2.

Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.

Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.

Redistribute the directly connected interfaces on R2.

NEW QUESTION 238
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.

NEW QUESTION 239
Refer to the exhibit.

Refer to the exhibit. The OSPF neighbor relationship is not coming up What must be configured to restore OSPF neighbor adjacency?

OSPF on the remote router

matching hello timers

use router ID

matching MTU values

NEW QUESTION 240
Refer to the exhibit.

The ACL is placed on the inbound Gigabit 0/1 interface of the router. Host
192.168.10.10cannot SSH to host 192.168.100.10 even though the flow is permitted. Which action resolves the issue without opening full access to this router?

Move the SSH entry to the beginning of the ACL

Temporarily move the permit ip any any line to the beginning of the ACL to see if the flow works

Temporarily remove the ACL from the interface to see if the flow works

Run the show access-list FILTER command to view if the SSH entry has any hit statistic associated with it

NEW QUESTION 241
Refer to the exhibit.

An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock. What is the reason for this error?

An authentication error with the NTP server results in an incorrect timestamp.

The keyword localtime is not defined on the timestamp service command.

The NTP server is in a different time zone.

The system clock is set incorrectly to summer-time hours.

NEW QUESTION 242
An engineer is troubleshooting on the console session of a router and turns on multiple debug commands. The console screen is filled with scrolling debug messages that none of the commands can be verified if entered correctly or display any output. Which action allows the engineer to see entered console commands while still continuing the analysis of the debug messages?

Configure the logging synchronous command

Configure the no logging console debugging command globally

Configure the logging synchronous level all command

Configure the term no mon command globally

NEW QUESTION 243
While troubleshooting connectivity issues to a router, these details are noticed:
* Standard pings to all router interfaces, including loopbacks, are successful.
* Data traffic is unaffected.
* SNMP connectivity is intermittent.
* SSH is either or disconnects frequently.
Which command must be configured first to troubleshoot this issue?

Show policy-map control-plane

Show policy-map

Show interface inc drop

Show ip route

NEW QUESTION 244
Which two statements about redistributing EIGRP into OSPF are true? (Choose two)

The redistributed EIGRP routes appear as type 3 LSAs in the OSPF database

The redistributed EIGRP routes appear as type 5 LSAs in the OSPF database

The administrative distance of the redistributed routes is 170

The redistributed EIGRP routes appear as OSPF external type 1

The redistributed EIGRP routes as placed into an OSPF area whose area ID matches the EIGRP autonomous system number

The redistributed EIGRP routes appear as OSPF external type 2 routes in the routing table

NEW QUESTION 245
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.

NEW QUESTION 246
Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?

router ospfv3 1
address-family ipv4

Router(config-router)#ospfv3 1 ipv4 area 0

Router(config-if)#ospfv3 1 ipv4 area 0

router ospfv3 1
address-family ipv4 unicast

Free 300-410 Exam Files Downloaded Instantly 100% Dumps & Practice Exam [Q225-Q246]

What's Next After Cisco ENARSI?