[2025] Valid 200-301 test answers & Cisco 200-301 exam pdf [Q256-Q273]

admin 200-301 Cisco December 14, 2025

5/5 - (1 vote)

[2025] Valid 200-301 test answers & Cisco 200-301 exam pdf

Verified 200-301 dumps Q&As – Pass Guarantee or Full Refund

Cisco 200-301 exam replaces the previous CCNA certification exams, and it is designed to align with the current industry trends and job roles. 200-301 exam tests the candidate’s ability to configure and troubleshoot network devices, as well as their knowledge of routing and switching concepts. It is a single exam that covers a broad range of topics and is suitable for individuals who are starting their careers in networking or are seeking to advance their careers.

NEW QUESTION 256
Drag and drop the statements about AAA from the left onto the corresponding AAA services on the right. Not all options are used.

Explanation:

NEW QUESTION 257
Refer to the exhibit.

Which outcome is expected when PC_A sends data to PC_B?

The switch rewrites the source and destination MAC addresses with its own.

The source MAC address is changed.

The source and destination MAC addresses remain the same.

The destination MAC address is replaced with ffff.ffff.ffff.

NEW QUESTION 258
A Cisco engineer is configuring a factory-default router with these three passwords:
* The user EXEC password for console access is p4ssw0rd1
* The user EXEC password for Telnet access is s3cr3t2
* The password for privileged EXEC mode is pnv4t3p4ss Which command sequence must the engineer configured

NEW QUESTION 259
A user configured OSPF in a single area between two routers.
A serial interface connecting R1 and R2 is running encapsulation PPP.
By default, which OSPF network type is seen on this interface when the user types show ip ospf interface on R1 or R2?

nonbroadcast

point-to-point

point-to-multipoint

broadcast

NEW QUESTION 260
Which two statements about Cisco Discovery Protocol are true? (Choose two)

It is used to initiate a VTP server and cient relationship

It uses SNMP to share device information to an external server

It runs on the network layer and the data link layer.

It runs on the data link layer only

It uses TLVs to share device information

NEW QUESTION 261
Refer to the exhibit.

Which command provides this output?

show ip route

show ip interface

show interface

show cdp neighbor

NEW QUESTION 262
Refer to the exhibit.

An engineer configured NAT translations and has verified that the configuration is correct.
Which IP address is the source IP?

10.4.4.4

10.4.4.5

172.23.103.10

172.23.104.4

NEW QUESTION 263
Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?

10.1.1.2

10.154.154.1

172.16.5.1

192.168.5.3

The highest IP address of all loopback interfaces will be chosen -> Loopback 0 will be chosen as the router ID.

NEW QUESTION 264
What is the primary purpose of a First Hop Redundancy Protocol?

It allows directly connected neighbors to share configuration information

It reduces routing failures by allowing Layer 3 load balancing between OSPF neighbors that have the same link metric

It allows a router to use bridge priorities to create multiple loop-free paths to a single destination

It reduces routing failures by allowing more than one router to represent itself as the default gateway of a network

Section: IP Services

NEW QUESTION 265
Under which condition is TCP preferred over UDP?

UDP is used when low latency is optimal, and TCP is used when latency is tolerable.

TCP is used when dropped data is more acceptable, and UDP is used when data is accepted out-of-order.

TCP is used when data reliability is critical, and UDP is used when missing packets are acceptable.

UDP is used when data is highly interactive, and TCP is used when data is time-sensitive.

Section: Network Fundamentals

NEW QUESTION 266
Which header field is new on IPv6?

Version

Hop Limit

Flow Label

Traffic Class

NEW QUESTION 267
A Cisco IP phone receive untagged data traffic from an attached PC. Which action is taken by the phone?

It allows the traffic to pass through unchanged

It drops the traffic

It tags the traffic with the default VLAN

It tags the traffic with the native VLAN

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/vlan/configuration_guide/b_vlan_152ex_2960-x_cg/b_vlan_152ex_2960-x_cg_chapter_0110.pdf

NEW QUESTION 268
An engineer is configuring an encrypted password for the enable command on a router where the local user database has already been configured Drag and drop the configuration commands from the left into the correct sequence on the right Not all commands are used

Explanation:

NEW QUESTION 269
Which option about JSON is true?

uses predefined tags or angle brackets () to delimit markup text

used to describe structured data that includes arrays

used for storing information

similar to HTML, it is more verbose than XML

NEW QUESTION 270
An engineer must configure an OSPF neighbor relationship between router R1 and R3. The authentication configuration has been configured and the connecting interfaces are in the same
192.168.1.0/30 subnet. What are the next two steps to complete the configuration? (Choose two.)

configure the hello and dead timers to match on both sides

configure the same process ID for the router OSPF process

configure the same router ID on both routing processes

Configure the interfaces as OSPF active on both sides.

configure both interfaces with the same area ID

Timers match by default.
The process ID can be the same or not.
The router ID mustn’t be the same.

NEW QUESTION 271
Refer to the exhibit.

A network engineer must provide configured IP addressing details to investigate a firewall rule Issue. Which subnet and mask Identify what is configured on the en0 interface?

10.8.0.0/16

10.8.64.0/18

10.8.128.0/19

10.8.138.0/24

NEW QUESTION 272
Drag the IPv6 DNS record types from the left onto the description on the right.

https://ns1.com/resources/dns-types-records-servers-and-queries#:~:text=Address%20Mapping%20record%20(A%20Record,a%20hostname%20to%20another%20hostname.